Ethylene oxide is produced by the catalytic oxidation of ethylene:
2C2H4 + O2 —? 2C2H4O
An undesired competing reaction is the combustion of ethylene:
C2H4 + 302
2CO2 + 2H2O
The feed to the reactor (not the fresh feed to the process) contains 3 moles of ethylene per mole of oxygen. The single-pass conversion of ethylene is 20%, and for every 100 moles of ethylene consumed in the reactor, 90 moles of ethylene oxide emerge in the reactor products. A multiple-unit process is used to separate the products: ethylene and oxygen are recycled to the reactor, ethylene oxide is sold as a product, and carbon dioxide and water are discarded.
- Assume a quantity of the reactor feed stream as a basis of calculation, draw and label the flowchart, perform a degree-of-freedom analysis, and write the equations you would use to calculate (i) the molar flow rates of ethylene and oxygen in the fresh feed, (ii) the production rate of ethylene oxide, and (iii) the overall conversion of ethylene. Do no calculations.
- Calculate the quantities specified in Part (a), either manually or with an equation-solving program.
Want to see the full answer?
Check out a sample textbook solutionChapter 4 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Additional Science Textbook Solutions
Process Dynamics and Control, 4e
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Starting Out with C++: Early Objects
Introduction to Java Programming and Data Structures, Comprehensive Version (11th Edition)
- ethylene oxide is prepared by oxidation of ethylene. 100Kmol of ethylene and 100Kmol of O2 are charged to a reactor.The percent conversion of ethylene is 85 and percent yield of C2H4O is 94.12. Calculate the composition of product steam leaving the reactor .The reactions taking place are: C2H4+0.5O2=C2H4O C2H4+3O2= 2CO2+2H2Oarrow_forwardFeed gas containing of 78.5mol % H₂, 21% of N₂ & 0.5% of Ar is mixed with recycle gas and enters a reactor where 15% N₂ is converted to NH3 as per the reaction. Ammonia from the exit of the reactor is completely separated from unconverted gases. To avoid the buildup of inerts, a small fraction (5%) of the unreacted gases purged and the balance recycled. USING ASPEN/HYSYS Draw the process flow sheet Product rate and Purge rate Basis:100mol/hrarrow_forward2. In an ethanol production plant, a separator produces a 99% ethanol product from a feedstock stream containing 85% water and 15% ethanol at a rate of 450 Ib/min. The separator has two outlet streams: the ethanol product outlet stream (99% ethanol) and a residual water stream. 30% of the feedstock is bypassed and mixed with the residual water stream leaving the separator. If 60% of the ethanol entering the separator is recovered in the product stream, determine the composition of the residual water stream just after leaving the separator and the composition of the residual stream after mixing with the bypass stream.arrow_forward
- N2(g) + 3H2 (g) > 2NH3 Given the feed to the reactor consist of 100mol/s N2 and 250 mol/s H2. Calculate the percentage of excess of the reactionarrow_forwardTitanium (Ti) is an important material in manufacturing airplane engines and frames. It is obtained from titanium tetrachloride (TiCl4), prepared from titanium dioxide, carbon, and chlorine through the following reaction: 3TiO2(s) + 4C(s) +6C2(g) -------à 3TiC4(g) 2CO2(g) + 2CO(g) a. If the reactor contains 11.34 g C, 13.56 g Cl2, and 8.3 g TiO2, identify the limiting reagent. b. Compute the theoretical yield of TiCl4. After the actual experiment, the reaction produces 13.48 g TiCl4. What is the percent yield of TiCl4?arrow_forward6- Floor beams of a transport airplane have been designed using an aluminum alloy containing 4.5 wt% Cu and 1.5 wt% Mg for a total weight of 95000 N. A customer has ordered the airplane but requested that its total weight be reduced by 10 percent for fuel saving purposes. An engineer in the design and analysis department has suggested that the weight saving objective can be accomplished by replacing the current aluminum alloy of the floor beams with another one containing 3 wt% Li and 1 wt% Cu. Is this possible? Answer the question by first determining the weight saving that will take place using the Al-Li alloy. Assume weighted averages of density and use the following densities for the mentioned materials: Al = 2.70 g/cm³ Cu = 8.92 g/cm³ Mg = 1.74 g/cm³ Li = 0.53 g/cm³arrow_forward
- The oxidation of ethylene to produce ethylene oxide proceeds according to the equation2C 2H 4 +O 2 ! 2C 2H 4OThe feed to a reactor contains 100 kmol C 2H 4 and 100 kmol O 2. If the reaction proceeds to completion, how much of the excess reactant will be left; how much C 2H 4O will be formed; and what is the extent of reaction?arrow_forwardTwo-hundred fifty pounds per hour of iron pyrites containing 90% FeS2 and 10% gangue are burned with 20% excess air based on conversion to SO3. The cinder discharged from the burner contains no sulfur. No conversion to SO3 occurs in the burner. The burner gas is passed through a converter which effects a 98% conversion of SO2 to SO3. The converter gas is passed to an absorber where all the SO3 is absorbed by 80% H2SO4 solution, which becomes 100% H2SO4 solution in the process. Establish a basis of one hundred pounds of iron pyrites Calculate: (a) the burner gas analysis, (b) the converter gas analysis, (c) pounds of 100% H2SO4 produced per 24-h day, if waste gas analyzes 0.19% SO2, 4.14% O2 and 95.67% N2arrow_forwardHematite is an iron ore with the following composition: Fe2O3 [MW=159.70]. To make steel, carbon [At. Wt. = 12.01] in the form of coke is used to reduce Fe2O3 to iron metal [At. Wt. = 55.85] as shown below: 3 C + 2 Fe2O3 → 3 CO2 + 4 Fe How many grams of carbon are needed to produce 2,500 grams of iron? Relative to the problem the processing of 798.5 g of hematite ore produced 508.2 g of iron metal. Determine the percent yield of pure iron for this batch?arrow_forward
- Acetylene reacts with HCl in appropriate conditions to form phenolic chloride C₂H3Cl, which is used in plastics industry, according to following reaction C₂H₂ + HCl → C₂H₂Cl If 35 g from acetylene react with 51 g from HCl, calculate: 1. Limiting reactant material. (8 degree) 2. Mass of residual reactant material. (7 degree) {CI= = 35.5 9 mole' H = 1 9 mole & C = 12} molearrow_forwardConsider the following simultaneous reactions: N2 + 3H2 → 2NH3(a) H2 + CO2 → CO + H2O (b) 550 mols are fed into the reactor, initially containing 67.4% H2, 21.3% N2 and the remainder CO2. The mixture at the outlet has 16% NH3 and 5% H2O (molar percentages). a- Calculate the degrees of advancement of reactions (a) and (b).arrow_forwardButane (C4H10)(C4H10) and dry air are fed to a combustion reactor at a steady rate of 45.9 mol/s45.9 mol/s butane and 2500.0 mol/s2500.0 mol/s dry air. Assume the butane reacts completely to produce CO2CO2 and H2O.H2O. The reactants enter the reactor at 25 ∘C25 ∘C and the products leave the reactor at 1110.4 ∘C.1110.4 ∘C. Calculate the percent excess air. Using the information below, find the heat interaction. Species ΔHf at 298 K(kJ/mol) CP (kJ/kmol·K) O2 0 3.5R N2 0 3.5R C4H10 -125.5 12R CO2 -393.5 3.5R H2O -241.8 3.5Rarrow_forward
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill EducationPrinciples of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
- Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill EducationChemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningElementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY