EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4.56P
436. The reaction between ethylene and hydrogen bromide to form ethyl bromide is carried out in a continuous reactor. The product stream is analyzed and found to contain 51.7 mole% C2H5Br and 17.3% HBr. The feed to the reactor contains only ethylene and hydrogen bromide. Calculate the fractional conversion of the limiting reactant and the percentage by which the other reactant is in excess. If the molar flow rate of the feed stream is 165 mol/s, what is the extent of reaction?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Methane (CH4) is reacted with oxygen (02) over a catalyst to produce acetlyene (C2H2) in the following reaction:
6 CHąlg) + O2lg) –→2 C2H2(g) + 2 CO(g) + 10 H2(g)
If a feed containing 150 mol CHg and 50 mol O, is fed into a reactor and the conversion of the limiting reactant is 92 %, determine the concentration of CH, in the product flue gas. Give your answer as a mole percent rounded off
to one decimal place.
1. Kindly answer this problem. Thank you.
In a chemical production plant, cyclohexane is made by the reaction of benzene and hydrogen. Reaction is as follows:
CHs + H2 → CoH12
The complete process of producing cyclohexane uses a reactor and a separator. Using the process shown below
and assuming 20 % excess hydrogen in the fresh feed, find the ratio of the recycle stream to the fresh feed
stream, the composition of the final product stream, and the composition of the stream leaving the reactor. The
overall conversion of benzene is 92% and the single-pass conversion is 21.5 %. The recycle stream is composed
of 23.9 % benzene and the remaining hydrogen.
Fresh
Feed
REACTOR
SEPARATOR
Product
Recycle
Chapter 4 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 4 - Prob. 4.1PCh. 4 - Rain is falling on a poorly designed 150-m" flat...Ch. 4 - A liquid-phase chemical reaction A -* B takes...Ch. 4 - A stream consisting of 44.6 mole% benzene and...Ch. 4 - Prob. 4.5PCh. 4 - A liquid mixture of acetone and water contains 35...Ch. 4 - Prob. 4.7PCh. 4 - Prob. 4.8PCh. 4 - Inside a distillation column (see Problem 4.8), a...Ch. 4 - Prob. 4.10P
Ch. 4 - In the production of soybean oil, dried and flaked...Ch. 4 - Prob. 4.12PCh. 4 - A process is carried out in which a mixture...Ch. 4 - Strawberries contain about 15wt% solids and 85wt%...Ch. 4 - Two streams flow into a 500-gallon tank. The first...Ch. 4 - A fuel distributor supplies four liquid fuels,...Ch. 4 - Prob. 4.17PCh. 4 - One thousand kilograms per hour of a mixture...Ch. 4 - L-Serine is an amino acid that often is provided...Ch. 4 - A 100 kmol/h stream that is 97 mole% carbon...Ch. 4 - A pharmaceutical product, P, is made in a batch...Ch. 4 - A liquid mixture containing ethanol (55.0 wt%) and...Ch. 4 - A stream of humid air containing 1.50 mole% H2O(v)...Ch. 4 - A liquid mixture contains 60.0 wt% ethanol (E),...Ch. 4 - Certain vegetables and fruits contain plant...Ch. 4 - Two aqueous sulfuric acid solutions containing...Ch. 4 - A paint mixture containing 25.0% of a pigment and...Ch. 4 - In the commercial production of sugar (sucrose),...Ch. 4 - Prob. 4.29PCh. 4 - A garment to protect the wearer from toxic agents...Ch. 4 - A dilute aqueous solution of H2SO4 (Solution A) is...Ch. 4 - Gas streams containing hydrogen and nitrogen in...Ch. 4 - An artificial kidney is a device that removes...Ch. 4 - The indicator-dilution method is a technique used...Ch. 4 - Prob. 4.35PCh. 4 - Gas absorption or gas scrubbing is a commonly used...Ch. 4 - The SO2 scrubbing tower described in Problem 4.36...Ch. 4 - Prob. 4.38PCh. 4 - The hormone estrogen is produced in the ovaries of...Ch. 4 - A liquid mixture containing 30.0mole% benzene (B),...Ch. 4 - Seawater containing 3.50 wt% salt passes through a...Ch. 4 - Inside the column a liquid stream flows downward...Ch. 4 - Prob. 4.43PCh. 4 - Effluents from metal-finishing plants have the...Ch. 4 - In an absorption tower (or absorber), a gas is...Ch. 4 - In the production of a bean oil, beans containing...Ch. 4 - Boilers are used in most chemical plants to...Ch. 4 - Following is a diagram of the shirt-cleaning...Ch. 4 - A drug (D) is produced in a three-stage extraction...Ch. 4 - Prob. 4.52PCh. 4 - Ammonia is oxidized to nitric oxide in the...Ch. 4 - Prob. 4.54PCh. 4 - A stream containing H2S and inert gases and a...Ch. 4 - 436. The reaction between ethylene and hydrogen...Ch. 4 - Prob. 4.57PCh. 4 - Prob. 4.58PCh. 4 - Titanium dioxide (TiCb) is used extensively as a...Ch. 4 - Prob. 4.60PCh. 4 - Prob. 4.61PCh. 4 - Oxygen consumed by a living organism in aerobic...Ch. 4 - A genetically engineered strain of Escherichia...Ch. 4 - The gas-phase reaction between methanol and acetic...Ch. 4 - Prob. 4.65PCh. 4 - Prob. 4.66PCh. 4 - Methane and oxygen react in the presence of a...Ch. 4 - Ethane is chlorinated in a continuous reactor:...Ch. 4 - Ethanol can be produced commercially by the...Ch. 4 - Prob. 4.70PCh. 4 - Solid calcium fluoride (CaF2) reacts with sulfuric...Ch. 4 - Prob. 4.72PCh. 4 - Chlorobenzene (C^HsCl), an important solvent and...Ch. 4 - A catalytic reactor is used to produce...Ch. 4 - 4.7'6. Methanol is produced by reacting carbon...Ch. 4 - Methane reacts with chlorine to produce methyl...Ch. 4 - Ethylene oxide is produced by the catalytic...Ch. 4 - Methanol is synthesized from carbon monoxide and...Ch. 4 - The fresh feed to an ammonia production process...Ch. 4 - A gas contains 75.0 wt% methane. 10.0% ethane....Ch. 4 - Five liters of liquid n-hexane and 4 liters of...Ch. 4 - Gasoline, which we will represent as having the...Ch. 4 - Prob. 4.87PCh. 4 - Natural gas containing a mixture of methane,...Ch. 4 - Propane is burned completely with excess oxygen....Ch. 4 - Prob. 4.91PCh. 4 - Prob. 4.92PCh. 4 - Liquid methanol is fed to a space heater at a rate...Ch. 4 - Prob. 4.94PCh. 4 - Prob. 4.95PCh. 4 - A fuel oil is analyzed and found to contain 85.0...Ch. 4 - Prob. 4.97PCh. 4 - Prob. 4.98PCh. 4 - Prob. 4.99PCh. 4 - 4.1 (Mt. You have been sent by the Environmental...Ch. 4 - Fuel oils contain primarily organic compounds and...
Additional Science Textbook Solutions
Find more solutions based on key concepts
Using PFE where required, find X(t) for a. X(s)=s(s+1)(s+2)(s+3)(s+4) b. X(s)=s+2( s+1)2 c. X(s)=1s2+s+1 d. X(s...
Process Dynamics and Control, 4e
The decomposition of cyclohexane to benzene and hydrogen is mass transfer–limited at high temperatures. The re...
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
Consider the following justification that the Fibonacci function, F(n) is O(n): Base case (n 2): F(1) = 1 and ...
Data Structures and Algorithms in Java
Compute the weakest precondition for each of the following assignment statements and postconditions: a. a = 2 ...
Concepts of Programming Languages (11th Edition)
Use the debugger to investigate the clock-display project. Set breakpoints in the ClockDisplay constructor and ...
Objects First with Java: A Practical Introduction Using BlueJ (6th Edition)
Determine the force P required to begin rolling the uniform cylinder of mass m over the obstruction of height h...
Engineering Mechanics: Statics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- A pilot plant reactor was charged with 50 kg naphthalene and 200 kg (98% by wt) H2SO4. The reaction goes to 90% completion. The product distribution was found to be 18.6% monosulfonate naphthalene and 81.4% disulphonate naphthalene. Calculate the complete analysis of the product.arrow_forwardCase: 1Sodium chloride is obtained by reacting NaOH with HCl in a batch reactor. NaOH + HCl → NaCl + H₂O Suppose that 100 kg of NaOH and 76 kg of HCL are taken in the batch reactor and 107 kg of NaCl is obtained after some time. Determine: The limiting reactant The percentage of excess reactant The degree of completion (fraction) The percent conversion of NaOH to NaCl The yield (kg of NaCl to kg of HCI) [Bhatt, B. I. & Vora, S. M. (2004)]arrow_forward2. In an ethanol production plant, a separator produces a 99% ethanol product from a feedstock stream containing 85% water and 15% ethanol at a rate of 450 Ib/min. The separator has two outlet streams: the ethanol product outlet stream (99% ethanol) and a residual water stream. 30% of the feedstock is bypassed and mixed with the residual water stream leaving the separator. If 60% of the ethanol entering the separator is recovered in the product stream, determine the composition of the residual water stream just after leaving the separator and the composition of the residual stream after mixing with the bypass stream.arrow_forward
- .edu bryuitra/courses roee_re Question Completion Status: The following process describes the complete combustion reaction of Toluene fuel C7HB (SG 0.866) with air. Liquid fuel (n1) enters the combustion chamber at 200mL/min, where it evaporated into a stream of air (n2) 15% in excess. Complete combustion reaction in which only fraction of the fuel is burned. The combustion products go to a condenser, where the unreacted fuel and water are liquified. The mass flowrate of the fuel in this steam (ma) is 50. The uncondensed gas leaves the condenser at 60 C and 0.5 atm gauge pressure. Calculate the fractional conversion of the fuel Calculate the SCMH of the air entering the combustion chamber Calculate the volumetric flow rate of the gas leaving the condenser (m³/min). a. b. C. ri4 CO2 n3 Fuel ris N2 Fuel ri1 ni4 CO2 nig O2 Combustion nig N2 Condenser air riz Chamber ng O2 ni, H,0 n3 Fuel niz H,0arrow_forwardI NEED THIS ASAP PLEASE. With step by step solution. Please, pleasearrow_forwardEthanol reacts with chlorine in a continuous reactor according to the equationC2H6 + Cl2 → C2H5Cl + HClA portion of the monochloroethane reacts with chlorine in an undesired side reaction according to the equationC2H5Cl + Cl2 → C2H4Cl2 + HClThe conversion of ethane is 13%, the selectivity of monochloroethane relative to dichloroethane is 13.3 and all the chlorine is consumed. Calculate the moles of each species in the outflow per 100 moles of monochloroethane produced.arrow_forward
- sunflower oil + 3methanol <--> 3 biodiesel product + glycerol A transesterification takes place by using sunflower oil and methanol and 1%wt. NaOH as catalyst. The ratio of sunflower oil to methanol is 1:6. 100g of sunflower oil will be used in this experiment. The result gives 60% glycerol yield. Calculate the mol and gr amount of the glycerol that is used according to these ratios: a) 1:6 b) 1:3 c)1:2arrow_forwardC22H4(g) + H2(g) --> C2H6(g) C22H4 flows into a catalytic reactor at 25.0 atm and 300°C with a flow rate of 957.3L/min. Hydrogen at 25.0 atm and 300°C flows into the reactor at a flow rate of 1500L/min. If 11.0 kg of C22H6 are collected per minute, what is the percent yield of the reaction?arrow_forwardN2(g) + 3H2 (g) > 2NH3 Given the feed to the reactor consist of 100mol/s N2 and 250 mol/s H2. Calculate the percentage of excess of the reactionarrow_forward
- A steady-state process to recover crystalline potassium chromate (K,CrOz) from an aqueous solution of this salt is required. Four thousand kilograms per hour of a solution that is one-third K,CrO, by mass is joined by a recycle stream containing 36.4% K2CrO7, and the combined stream is fed into an evaporator. The concentrated stream leaving the evaporator contains 49.4% K,CrO; this stream is fed into a crystallizer in which it is cooled (causing crystals of K,CrO, to come out of solution) and then filtered. The filter cake consists of K,CrO, crystals and a solution that contains 36.4% K,CrO, by mass; the crystals account for 95% of the total mass of the filter cake. The solution that passes through the filter, also 36.4% K,CrO,, is the recycle stream. 1- Draw the flowchart of the system and put all known information. 2- Calculate the rate of evaporation, the rate of production of crystalline K,CrO7, the feed rates that the evaporator and the crystallizer must be designed to handle, and…arrow_forward1. Aluminum sulfate can be made by the following reaction: 2AlCl3(aq)+3 H2SO4(aq)➡Al(SO4)3(aq)+6HCl(aq). It is quit soluble in water, so to isolate it the solution has to be evaporated to dryness. This drives off the volatile HCl, but the residual solid has to be heated to a little over 200 celsius to drive off the water. In one experiment, 25.0 g of AlCl3 were mixed with 30.0 g of H2SO4. Eventually, 28.46 g of pure Al2(SO4)3 were isolated. Calculate the percentage yield. 2. The potassium salt of benzoic acid, potassium benzoate (KC7H5O2), can be made by the action of potassium permanganate on toluene (C7H8) as follows: C7H8+ KMnO4➡ KC7H5O2+ 2MnO2+ KOH+ H2O. If the yield of potassium benzoate cannot realistically be expected to be more tha 71%, what is the minimum number of grams of toluene needed to achieve this yield while producing 11.5g of potassium benzoate? 3. A chemist set up a synthesis of phosphorus trichloride by mixing 12.0g P with 35.0g Cl2 and obatained 42.2 g of PCl3.…arrow_forwardTitanium (Ti) is an important material in manufacturing airplane engines and frames. It is obtained from titanium tetrachloride (TiCl4), prepared from titanium dioxide, carbon, and chlorine through the following reaction: 3TiO2(s) + 4C(s) +6C2(g) -------à 3TiC4(g) 2CO2(g) + 2CO(g) a. If the reactor contains 11.34 g C, 13.56 g Cl2, and 8.3 g TiO2, identify the limiting reagent. b. Compute the theoretical yield of TiCl4. After the actual experiment, the reaction produces 13.48 g TiCl4. What is the percent yield of TiCl4?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Mod-01 Lec-23 Degrees of freedom analysis; Author: nptelhrd;https://www.youtube.com/watch?v=c4h85JjrkzQ;License: Standard YouTube License, CC-BY
Introduction to Degrees of Freedom; Author: LearnChemE;https://www.youtube.com/watch?v=tW1ft4y5fQY;License: Standard Youtube License